Text preview for : china_akira_ct21ni9r_ch_3s10__with_st92195_stv2248_strg6653__-_adj_164.pdf part of . Various china akira ct21ni9r ch 3s10 with st92195 stv2248 strg6653 - adj 164 . Various CHINA TV TV Div Service Mode`s chinese TV`s china_akira_ct21ni9r_ch_3s10__with_st92195_stv2248_strg6653__-_adj_164.pdf
Back to : china_akira_ct21ni9r_ch_3 | Home
6
ALIGNMENT INSTRUCTION (3S10)
1. Preface
This ADJUST MANUAL is only used for 3S10 chassis, and guides to make adjust equipments. It
is only a reference.
2. Instruments For Adjustment
a. TV signal generator
b. 20MHz 2-channel oscilloscope
c. Adjust jigs
d. Sweep Signal Generator(option)
e. Digital voltmeter
f. White balance adjust equipment.
3. How To Enter And Exit Factory Mode
a. Enter factory mode by pressing MENU button, AV button and ANAL button in turn or
pressing the SERVICE button (on the right of MENU button, we can add this button for
easy to enter service mode in factory). Press OK to enter Service 2.0 and Design mode.
b. Exit factory mode by pressing PP or pressing STANDBY button.
4. Chassis Adjust
4-1. VCO Adjust
a. Set TV Signal Generator to output a 38.9MHz, stranger than 80dBuv PAL color bar
signal.
b. Signal inputs to TUNER's IF terminal or pin5 of SAW101 through a 0.01UF/50V
capacitor
c. Connect 220V AC (50/60Hz) and Switch on power switch. Enter Service 2.0 menu.
d. Press AV button after picking out VCO Coarse or VCO Fine item by PROG+/- buttons.
VCO is well adjusted automatically if the character OK appears at the bottom of screen.
(If OK can not appear automatically, please fine tune LC238 and re-try again)
e. The following adjustment is suitable for TV sets with SECAM L/L' system.
Set TV signal Generator to output a 34.4MHz Signal, set TV set to VHF-L band. Press
AV button after picking out VCO Coarse L1 or VCO Fine L1 by PROG+/- buttons. The
VCO of SECAM L' system is well adjusted if the character OK appears automatically at
the bottom of screen.
Note: After VCO is well adjusted, exit factory mode by pressing PP button at first, switch
off power switch, then withdraw IF signal.
4-2. IF Trap(LC101) Adjust For RF NTSC
a. Receive RF NTSC signal.
b. Adjust LC101 until picture is best.(We also can use a sweep sigmal generator to get best
the trap point)
4-3. AGC Adjust
a. Receive 60dBuV RF signal.
b. Enter Service V2.0 mode and get Tuner AGC PAL item, adjust PAL AGC by VOL+/-
buttons until picture's noise just disappears and no distortion under 100dBuV level.
c. If TV has SECAM LL1 system, enter Service V2.0 mode and get Tuner AGC LL1 item,
adjust SECAM LL' AGC by VOL+/- buttons until picture's noise just disappears and no
distortion under 100dBuV level.
c. If TV has SECAME LL1 system, press OK key to enter design menu, set AGC Gain PAL
to 1,set AGC Gain LL1 to 3
Model No: CT-21NI9R
Version 1.0
7
4-4. Main Power Adjust (B+)
a. Switch on power switch.
b. Measure the voltage with digital voltage meter between two terminals of C615.
d. Adjust VR601 to obtain 110+/-0.5V on the Digital Voltage meter. (The voltage will have
a little difference when use difference type of CRT.ORION A51JSW91X50 CRT is
118V;HITACH CRT is 110V)
5. Complete TV General Adjust
5-1. Screen Voltage Adjust(G2).
Set TV set to factory mode without signal input. Then press MUTE button, a horizontal line
appears.
a. Adjust the "SCREEN" knob of FBT until a horizontal line is just can be seen.
b. Pressing MUTE button to exit one line mode.
5-2. Focus Adjust
a. Receive CROSS HATCH PATTERN, set picture to Dynamic statue by pressing PP
button.
b. Adjust the "FOCUS" knob of FBT to get a most clear picture.
5-3. White Balance Adjust.
Receive black & white pattern (PAL SYSTEM)
a. Set picture to Standard statue, adjust white balance equipment to get 2cd/m2 at low
brightness and 100cd/ m2 at high brightness.
b. Enter white balance adjust mode of factory mode. Two probes of white balance
equipment close up the low brightness and high brightness area.
c. Adjust Red Gain, Green Gain, Blue Gain; DC Red, DC Green, (DC Blue is better to
fixed to 64) using remote handset to meet factory requirement. Button's function refers to
the following table.
Remote handset:
5-4. Horizontal/Vertical Central Adjust
a. Receive MONOSCOPE PATTERN.
b. Get H Position item, use VOL+/- buttons to set H center of the picture to meet factory
requirement.
c. Vertical central can not be adjusted by IIC bus. But we can use a 1.5K /2W resistor (R312
or R311 )or omit it to adjust it
Model No: CT-21NI9R
Version 1.0
8
5-5. SUB-Brightness Adjust
a. Receive GREY SCALE/COLOR BAR pattern.
b. Enter Service V2.0 mode.
c. Press PROG +/- buttons to select Bright Max. Set a fixed value by VOL+/- buttons (The
value will be difference when use difference type of CRT.. ORION A51JSW91X50 CRT
is 63).
d. Press ANAL button to get Bright Min item and bright, contrast, color become zero
automatically. Press VOL+/- buttons to make the second darkness bar of GREY SCALE
part loom. Press PIC again to exit this mode
5-6. Vertical Amplitude Adjust
a. PAL system: adjust under VAMP 50.
b. NTSC system: adjust under VAMP 60.
5-7 Sub-Tint adjust
a. Receive NTSC RF signal. Set main Tint to center (zero).
b. Set TV set in SERVEICE V2.0 mode and get Sub Tint item.
c. Adjust SubTint using VOL+/- buttons until tint is best.
5-8 Set Picture's Standard Data
1. Adjust brightness/contrast/colour to the best mode you think Standard should be.
2 Enter white balance adjust mode, then press S.MODE key, MCU will store current
brightness/contrast/colour data into Standard
5-9 Apr Threshold Adjust
It is at the item of white balance adjustment menu. Apr means Automatic RGB Peak
Regulation. It is used to increase the contrast of pictures with low contrast and avoid clipping
at RGB output for picture with high peak amplitudes. Chang it's value to get perfect contrast
quality of picture. It maybe different when use different CRT.( ORION A51JSW91X50 CRT
sets 15)
5-10 E-W correction And H-Wide Adjust For Pure Flat CRT
a. Receive cross pattern and set picture in Standard mode use PP key
b. Adjust VR801 to set picture's wide
c. Adjust VR802 to get a good linear pattern
d. Adjust VR801 to set picture's wide if it is changed after adjust VR802
Model No: CT-21NI9R
Version 1.0
9
DESIGN FOR ST92195 AND SET OPTIONS
OPERATING:
Use MENU+AV+ANAL key to enter factory mode, OK key to enter Service 2.0 mode and Design
mode. Use PP key to exit Factory mode. Use PROG+/- keys to select adjust item, use VOL+/- keys to
set data.
AGC Gain: usually set to zero.
The initializations of Option1-5 are zero.
Option 1:
b7 b6 b5 b4 b3 b2 b1 b0
+ 0/1 OFF/ON LOGO
+ 0/1 OFF/ON INTER CARRIER/QSS FORT NICAM
+ 0/1 OFF/ON HIGH GAIN TUNER
+ 0/1 SAFE (X-RAY) PROTECT ON/OFF
+ 0/1 OFF/ON CUT OFF LOOP
+ RESERVE
+ 0/1 OFF/ON INTER CARRIER/QSS WITHOUT NICAM
Option 2:
b7 b6 b5 b4 b3 b2 b1 b0
+ 0/1 OFF/ON CORING WHEN PEAKING
+ 0/1 OFF/ON AUTO FLESH WHEN NTSC
+ 0/1 OFF/ON BLACK STRETCH
+ 0/1 ON/OFF APR
+ 0/1 OFF/ON COLOR +6Db
+ RESERVE
+ 0/1 TWO LANGUAGE/ONE LANGUAGE OSD
Option 3:
b7 b6 b5 b4 b3 b2 b1 b0
+ 0/1 TDA7449/TDA7439
+ 0/1 TDA1905/TDA7496
+ 0/1 OFF/ON MANUAL/AUTO CUTOFF
+ 0/1 ON/OFF SECAM LL' FOR FRANCE
+ 0/1 PIF OVERMODULATION
Option 4:
b7 b6 b5 b4 b3 b2 b1 b0
+ 0/1 OFF/ON AV1(AV)
+ 0/1 OFF/ON AV2
+ 0/1 OFF/ON SVHS
+ 0/1 ON/OFF RGB
+ 0/1 NOT USED
Model No: CT-21NI9R
Version 1.0
10
Option 5:
(Only used for TVs with teletext)
Used to select teletext languages for different area use
b0 = enable the remote controller to change Run_Time_Mode_Choice use "MENU" key
b1, b2 = "Run_Time_Mode_Choice" ---------- set to 0/2/4/6!!
Teletext languages option
MCU1
0: ENGLISH, CYR2_LAT_Twist, SWEDISH, CZECH, ENGLISH, SERBIAN, LETTISH,
AR_LAT_Twist
1: POLISH, CYR2_LAT_Twist, ESTONIAN, CZECH, ENGLISH, SERBIAN, LETTISH,
RUMANIAN
2: ENGLISH, CYR2_LAT_Twist, SWEDISH, CZECH, ENGLISH, SERBIAN, LETTISH,
FARSI_LAT_Twist
3: POLISH, CYR2_LAT_Twist, SWEDISH, CZECH, ENGLISH, SERBIAN, LETTISH,
FARSI_LAT_Twist
MCU2
0: ENGLISH, FRENCH, SWEDISH, TURKISH, GERMAN, PORTUGUESE, ITALIAN,
RUMANIAN
1: ENGLISH, CYR2_LAT_Twist, SWEDISH, CZECH, GERMAN, CYR3_LAT_Twist,
ITALIAN, RUMANIAN
2: POLISH, FRENCH, SWEDISH, CZECH, GERMAN, SERBIAN, LETTISH, RUMANIAN
3: POLISH, CYR2_LAT_Twist, ESTONIAN, TURKISH, GERMAN, CYR3_LAT_Twist,
LETTISH, RUMANIAN
Notes:
CYR2_LAT_Twist: Russian
Swedish: Swedish/Hungarian
Czech: Czech/Slovak
Lettish: lettish/Lithuanian
Serbian: Serbian/croarian/slovanian
FARSI_LAT_Twist : Persian
Note for option:
Option1: b4----always set 0
Option2:
b0---- usually set 0 can reduce picture's noise
b1--- usually set 0 can auto revise tint of NTSC
b2--- usually set 0 make picture's contrust better
b3--- usually set 0 make picture's contrust better
b4--- usually set 0 enlarge colour
Model No: CT-21NI9R
Version 1.0
11
Option3:
b0---- always set 0
b1--- MCU's MUTE pin output voltage select. Set to 0 when use TDA1905(MUTE=0V), set to 1 when
use TDA7496(MUTE=5V)
b2--- always set 0
b3--- usually set 0
b4--- usually set 0
Option4:
Only one AV input: b0=1 b2=0
Two AVs input : b0=1 b1=1
When SCART need, b0=1 b3=1
HPOS OSD: OSD left and right position, set to 001
VPOS OSD: OSD up, and under position, set to 01
HPOS TXT: teletext character left and right position
VPOS TXT: teletext character above and under position
LOGO set:
1 Set OPTION1 b0=1.
2 The last item of white balance adjustment mode is used to set LOGO there are most 12 characters
to select .Use PROG+/-, VOL+/- buttons to change character. The highest bit means LOGO
characters' number, it can be set among 1, 2, 3, 4, 5, 6, 789ABC.
Note:
The data of the above adjustment is written into IC002(24C08EEPROM).
IC002 used on the product line must be well written data. If use a blank EEPROM (the interior data are
set to FF) or not suitable for 3S10 chassis' EEPROM, it will be initialized (all data set to 00) and the
special data will be written automatically when switch AC power on at the first few seconds. The
values are following:
White Balance Adjust Menu
Red Gain 32
DC Red 063
Green Gain 32
DC Gain 063
Blue Gain 32
DC Blue 063
Apr Threshold 10
LOGO 6
Model No: CT-21NI9R
Version 1.0
12
Service V2.0 | Desing
Tuner AGC 32 | AGC Gain 00
H Position 32 | Option1 00
V Position 32 | Option2 00
VAMP 50 32 | Option3 00
VAMP 60 32 | Option4 00
Bright Max 63 | Option5 00
Bright Min 00 | ST Ttext 00
Sub Tint 32 | HPOS OSD 001
VCO Coarse 05 | VPOS OSD 01
VCO Fine 63 | HPOS TXT 057
VCO Coarse L1 05 | VPOS TXT
VCO Fine L 1 080 |
* The above values are automatically initializations. The purpose is to convenient for service
out of factory. IC002 must be re-adjusted before being used in assembly line.
** In factory, we can set one chip of EEPROM as a model first and copy it to others.
Procedure for 3S10 Chassis (Only for reference)
1. Touch up line:
a. B+ voltage adjust
b. VCO adjust
c. IF trap adjust for NTSC-M system.
This can be done in FA line according to your option. We can adjust LC101 to get perfect
NTSC-M system picture's quality and no disturbance of SIF signal.
2. Final Assembly Line:
a. Screen and Focus voltage adjust
b. TAGC adjust
c. White balance adjust
d. H/V central and V Amp 50 adjust for PAL
e. Bright Min adjust
f. V AMP 60 and Sub Tint for NTSC
Model No: CT-21NI9R
Version 1.0