| Make | Model | Problem | Solution | Date |
| | | |
| Found: 225
|
| Alba | CTV743 | Channel No's but no H.T. | D806 s/c | 14-09-04 |
| Alba | CTV743 | Dead apart from chan no's | D806 1N4936 s/c - used BYD33M | 14-09-04 |
|
|
| Alba | CTV743 | FIELD COLL + NO SOUND | R435 2R D406 SC | 14-09-04 |
| Alba | CTV743 | NO PIC OR SOUND 7 IN DISPLAY | D406 SC R435 OC 1R | 14-09-04 |
| Alba | CTV743 | No sound & field coll | R435 2R safety res o/c, D406 s/c | 14-09-04 |
| Alba | CTV743 | No start up & ch7 displayed | D406 BY228 s/c & R435 1R 1w o/c in line o/p stage | 14-09-04 |
| B & O | 7433 | Txt int & int sync txt | Tr3 & 4 vid amps and adj | 14-09-04 |
| B&O | 7430/7702 | int pic | TR2 BC338 on left of pcb int o/c b-e | 14-09-04 |
| Bush | 1430 | R/C not working | If TFMS 1340 or 1360 IR sensor reciever used then its probably faulty | 14-09-04 |
| Bush | 1433 | BLANK SCREEN WITH THREE LINES AT TOP L/H SIDE THEN UNIT SHUTS DOWN | INPUT ANTI-THEFT PASSWORD WITH REMOTE OR CONTACT TECHNICAL FOR PASSWORD | 14-09-04 |
| Bush | 1433 | Dead | R804 820k start up resistor o/c | 14-09-04 |
| Bush | 1433 | Dead | R809 0R47 o/c, R805 330k ?w o/c, Q801 BUZ77B s/c | 14-09-04 |
| BUSH | 1433 | DEAD | REPLACE R809 0.47OHMS | 14-09-04 |
| Bush | 1433 | DEAD | REPLACE R802 75K2W | 14-09-04 |
| Bush | 1433 | Dead - chopper FET BUZ77B s/c, R809 0R47 o/c | Chopper tfmr HR9104 | 14-09-04 |
| Bush | 1433 | dead - primary ht only | R804 820k o/c | 14-09-04 |
| Bush | 1433 | off | chopper tfmr faulty caused demise of R809 4R7? Q801 FET BUX77B & TDA4605 | 14-09-04 |
| Bush | 1433 | off with BUZ77B s/c & 0R47 o/c | replace BUZ77B, TDA4605-2, 0R47, check R805 330K R803 820k and caps also for s/c pri winding of chopper tfmr | 14-09-04 |
| Bush | 1433 | Small pic HT low at 89v | HT res cap 47µ 160v hot & bothered | 14-09-04 |
| Bush | 1433 | St/by only | Check R804 330k & R805 820k in psu, FET & TDA4506. Also, if front buttons broken, punter may have damaged connections to print around X501 | 14-09-04 |
| Bush | 1433 | When replacing TDA4605 | If after replacement, st/by LED flashes & difficult to turn on - also 112v HT low at 107v try a different TDA4605- it worked for me! | 14-09-04 |
| Bush | 1433 11AK20 | Blank screen with 3 lines top lh of screen then shuts down (Anti-theft password set) | Enter correct password! | 14-09-04 |
|
|
| Bush | 1433 11AK20 | Bright B pic with FB lines | Q907 BF423 leaky or equiv in other col | 14-09-04 |
| Bush | 1433 11AK20 | Dead | R802 75k 2w o/c or R809 0R47 o/c | 14-09-04 |
| Bush | 1433 11AK20 | Dead - internal fuse intact | power surge blown bridge rects - replace also safety res 2R2 5w | 14-09-04 |
| Bush | 1433 11AK20 | Int dead or reverting to st/by | Dry joints IC802 reg & IC401 jungle chip (under IF shielding plate) | 14-09-04 |
| Bush | 1433 11AK20 | LH side pic purple, RH side green | IC402 STV2180A faulty | 14-09-04 |
| Bush | 1433 11AK20 | No pic - sound ok | Loptx arcing with C615 - LOPTx faulty | 14-09-04 |
| Bush | 1433 11AK20 | No pic/sound - HT ok | D604 BA157 LOPTx sec s/c | 14-09-04 |
| Bush | 1433 11AK20 | St/by only | No clock/data between IC502 EEPROM & Micro replace EEPROM pt no ALBA3621624020 | 14-09-04 |