Make | Model | Problem | Solution | Date |
| | | |
Found: 74
|
Conti | 20KV7 Beko | Reverts to st/by at sw on | IC701 TDA6107Q on crt base | 14-09-04 |
Ferguson | ICC7 B59F | St/by only | DL18 1N4148 leaky | 14-09-04 |
|
Ferguson | ICC7 B59F | Video response poor with streaking | R704 1k5 on crt base hi res | 14-09-04 |
GEC | TVC2437B | Int off - no power LED | Dry joints PSU R183 22k & tfmr | 14-09-04 |
Mitsubishi | C14M7B Daewoo | Field collapse | Replace IC 301 TDA8356, & replace smoothing cap C309(47uF) with 22uf (ECEA 2A220)160 Volts. Across legs of capacitor fit a 0.1uF (ECQM2A104J),and the link marked R420 replace with 2R2/.5W safety resistor (ERQICI2HCJ2R2). Also check supply rail diode.(Part numbers are Panasonic BTW) | 14-09-04 |
Mitsubishi | C21T7B | Fine hor lines across screen | IC951 TDA8171 FOP chip | 14-09-04 |
MITSUBISHI | C21T7B | FINE HORIZONTAL LINES ON SCREEN | REPLACE FRAME IC951 IC**TDA8171 | 14-09-04 |
Mitsubishi | C2557B | No Menu, OSD or able to acess service mode | IC702 EEPROM Mits274P747010 | 14-09-04 |
Mitsubishi | C25C7B | Col flashes on screen, col sat varies - int | Dry joint Chroma Xtals X601 & 602 | 14-09-04 |
Mitsubishi | C25C7B | Dead - Green LED fast flashing - after psu repair | Q901, Q552, D909 s/c, R991 o/c, C914 47µ low cap & Q501 leaky | 14-09-04 |
Mitsubishi | C25C7B | Field collapse & no sound | Z551 o/c due to D507 s/c & IC551 E/W chip s/c pin 6 | 14-09-04 |
Mitsubishi | C25C7B | FRAME COLLAPSE AND NO SOUND | REPLACE Z551, D507, AND IC551 | 14-09-04 |
Mitsubishi | C25C7B | Int no green aft 30 mins | IC660 TEA50101B on crt base | 14-09-04 |
Mitsubishi | C25C7B | INT NO GREEN LOOKS LIKE CRT | REPLACE IC660 ON CRT BASE | 14-09-04 |
Mitsubishi | C25C7B | No pic aft 5-10 mins - sound ok | Dry joints Xtal resonator X701 | 14-09-04 |
Mitsubishi | C25D7B | NO SURROUND SOUND | SELECT SPECIAL MENU,ENSURE "STANDARD TV" IS "OFF" SWITCH OFF FOR 30 SECS | 14-09-04 |
Mitsubishi | C25D7B | No surround sound - when selecting in menu it shows "OFF" & can't be turned back on | Software bug - select special menu & ensure "Standard TV" is set to "Off", sw off for 30 secs. Sw back on & Surround sound can now be set | 14-09-04 |
Mitsubishi | C25D7B | Slow start up, no Txt, juddering pic & vol slow | EEPROM faulty Pt no MITS274P747010 & change IC701 Pt no MITS274P755050 | 14-09-04 |
Mitsubishi | C2857B | Dead with st/by light flashing | All PSU sec volts ok - line dr at LOPTr base dist - Q501 faulty (OK tested out of cct) | 14-09-04 |
Mitsubishi | C28C7B | Int col & blows Q552 LOPTr | Dry joints earth links grounding C607 & pin 30 IC201 Jungle chip | 14-09-04 |
Mitsubishi | C28C7B | No pic - sound ok | C655 0µ015 2kv leaky | 14-09-04 |
Mitsubishi | C28C7B | NO SOUND | FAULTY NICAM PCB | 14-09-04 |
|
Mitsubishi | C28C7B | No sound | NICAM PCB Pt no 921C216005 | 14-09-04 |
Mitsubishi | C28C7B | No sound or pic, HT at 145v & Green LED flashing | Q501 JC501R line dr Tr leaky - Pt no MITS260P748030 | 14-09-04 |
Mitsubishi | C28D7B | No sound | IC3A1 IC3A2 and IC3B1. It is always the middle one that goes s/c and blows Z902 which then removes the 28v supply to these ICs. You can check which one is s/c by unsoldering pin 9 of each ic one at a time and the check for s/c across PLUG DE which is the 28v supply | 14-09-04 |
Mitsubishi | CT1447BM | Dead | IC901 STR44115, D906 (RG2) protection diode, R901 (4r7/7W) and C921 (47µF/50V). | 14-09-04 |
Mitsubishi | CT2117BM | Col cycles thro' auto grey scale at sw on with flashing lines | Caused by High HT - C911 33µ 50v, C910 33µ 50v & C913 100µ all hi esr | 14-09-04 |
Mitsubishi | CT2227BM | Dead - int dead | Dry-joints on line driver transformer | 14-09-04 |
Mitsubishi | CT2227BM | field collapse with burning smell | C412 330µ and C413 | 14-09-04 |
Mitsubishi | CT2227BM | No sound or raster. | R7A0 ( 1.2ohm ) o/c on remote panel. | 14-09-04 |