Make | Model | Problem | Solution | Date |
| | | |
Found: 56
|
Sony | BE-3D | EW dist | IC800 LM393P, D800 ISS133T both leaky | 14-09-04 |
Sony | BE-3D | int bright blue pic - trips | crt faulty | 14-09-04 |
|
Sony | BE-3D | No sound | IC1200 TDA7264 | 14-09-04 |
Sony | BE-3D | St/by only | lopt | 14-09-04 |
Sony | BE-3D | To enter service mode | press OSD, "5", vol+ & TT Technology You Can Taste project booklet | 14-09-04 |
Sony | BE-3D KV25F3U | dead, no 135V | o/c print around D609 | 14-09-04 |
Sony | BE-3D KV25F3U | no audio output | no +21V, PS602 2.7A o/c (153268621) | 14-09-04 |
Sony | BE-3D KV25X1U | burst of EHT for 5 sec, then dead | LOPTx (145316912) | 14-09-04 |
Sony | BE-3D KV25X1U | dead, HT down to 24V | no 5V supply, replace IC604 (875936613) | 14-09-04 |
Sony | BE-3D KV25X1U | dead, no LED | IC600 STRS6707, R605 0.27R o/c | 14-09-04 |
Sony | BE-3D KV28WF1U | no pic (unless contrast and brightness are fully up) | R828 22k on LOPTx pin 7 gone high | 14-09-04 |
Sony | BE-3D KV28WF1U | pic does not zoom forward or back in widesreen zoom mode | this is correct for TV, once in zoom mode the remote would only move pic up or down (for subtitles etc) | 14-09-04 |
Sony | BE-3D KV28WS2U | buzzing on sound, IC260 gets hot | resolder earth pin on plug CN303 | 14-09-04 |
Sony | BE-3D KV28WS2U | int no remote | IR receiver IC900 894179051 | 14-09-04 |
Sony | BE-3D KV28WS2U | no pic, sound Ok | no line drive, R870 1R 1W o/c | 14-09-04 |
Sony | BE-3D KV28WS2U | no sound | D613 FMN-G12S o/c (871905838) | 14-09-04 |
Sony | BE-3D KV28WS2U | vol goes up or down on its own, channels wipe out of memory, unusual characters on LHS | int lockup of IC3, replace with new software type (IC3 TMS27PC0200-15 software 15FMBW706 or later, part number 875945310) | 14-09-04 |
Sony | BE-3D KV29F2U | green flyback lines, then goes dead within 10 sec | Q707 BF423 leaky on CRT | 14-09-04 |
Sony | BE-3D KV29F2U | no sound from cold for 30 min | replace IC3 875947773 | 14-09-04 |
Sony | BE-3D KV29F3U | int sound muting, locking up and no tuning memory | NVM IC2 975933420 | 14-09-04 |
Sony | BE-3D KV29F3U | poor CRT purity | replace C632 as the degaus relay is not energising | 14-09-04 |
Sony | BE-3D KV29X1U | no pic, rainbow effect if A1 increased | 9V supply high at 11.6V, replace IC606 LM2940T-9-0 | 14-09-04 |
|
Sony | BE-3D KV32WF1U | no pic or sound, PSU screaming | LOPTr Q802 2SC5251 s/c | 14-09-04 |
Sony | BE-3D KV32WF1U | no sound | fuse PS602 N75 o/c, IC1200 TDA7264 s/c, mute transistors Q1200 2SC1740 and Q1201 DTC143TS | 14-09-04 |
Sony | BE-3D KV32WF1U | stuck in stby | Q812 (872904286) s/c, D802 (871903849) s/c, LOPTx (145325711) u/s | 14-09-04 |
Sony | BE-3D KV32WS2U | low/varying height | C616 1000uF 25V in PSU | 14-09-04 |
Sony | BE3D | Brief rustle of EHT at sw on, psu ok but no line dr or error code | Set in over current mode - check volts at coll Q606, normally 0v - if volts present set is in overcurrent mode indicating fault in LOP | 14-09-04 |
Sony | BE3D | Buzzing only on sound - incorrect sound system selected | audio system can be changed by altering "destination" of set. PAL I can be selected by putting set into service mode as described in the service manual. At "TT" prompt enter "24". After re-tuning set,
sound should return to normal. | 14-09-04 |
Sony | BE3D | Dead , burst of EHT at sw on, no st/by | LOPTx HR7337 | 14-09-04 |
Sony | BE3D | E-W bowing | Q532 fet replaced - was dry joints & check for other dry joints | 14-09-04 |