| Make | Model | Problem | Solution | Date |
| | | |
| Found: 55
|
| Thomson | 14CB25UT | Dead with psu running | Fuse FW002 on video board | 14-09-04 |
| Thomson | 20CB25UT | Int no response to any controls, int no sound or pic at start up | After checking EEPROM by replacement discovered micros clock not running - not Xtal but 2 x sm caps in xtal osc cct | 14-09-04 |
|
|
| Thomson | 20CB25UT | TV cuts out aft 10 secs - video sect dead | R002 1R o/c on video | 14-09-04 |
| Thomson | 21CB26VN | Dead - psu works on dummy load | RP531 100R sm o/c (had prev had FOP chip IF01 & chopper FET TP20 changed) | 14-09-04 |
| Thomson | 28WF45E | No B | No B-Y signal. IV100 TDA9178 U/S. | 14-09-04 |
| Thomson | 32WS83KP | Dead & tripping | HT ok at 95v when lop dis'd - IB01 TEA5101B RGB o/p chip on crt base | 14-09-04 |
| Thomson | 32WT45U | Flyback lines then pulsing pic when A1 reduced | LOPTx 10675710 | 14-09-04 |
| Thomson | ICC11 | TV thomson ICC11 (63DF89L) shut down itself brusquely, the red LED on front panel also led switch off a few seconds after. the TV is in this status during 5 to 15 seconds, after the red led flashing about 5 times and the TV restart (and LEd switch normall | Try to bridge pin 03-04 on IL 001, that way youŽll inactivate security-stops of the chassis... The TV will work now. There must be a dammage within the security-circuit of the chassis! Try to repair and allocate the dammage for drive the TV on secure standarts! | 02-07-05 |
| Thomson | ICC11 72MK89D | Excess brightness with fb lines | RL128 1M8 in A1 pot divider on dynamic focus module | 14-09-04 |
| Thomson | ICC11 72MK89D | Luminance lost | Check with scope pin 14 Pl/skt BV001. If vid signal missing or crushed check T130, 132 & 134 in IF module. If good signal here check vid signal at TV001 under screen in vid module. If no sig here TV681 &/or TV682 can be responsible. If sig at TV001 ok, TV002/3 are faulty | 14-09-04 |
| Thomson | ICC17 | Dead - no main psu start up | Crack in print front control panel - no supply for st/by LED & R/C rx | 14-09-04 |
| Thomson | ICC17 | Destroys LOPTrs & E/W unstable | CL22 22nf 1kv O/C across E/W diode | 14-09-04 |
| Thomson | ICC17 | EW faulty | DL22 BYW76 leaky, TL41 BD241C driver u/s, TL42 BC546B u/s, s/c across DL42 caused by IV01 64 pin sm TDA8855H jungle chip | 14-09-04 |
| Thomson | ICC17 | Excess width & E-W faulty | TL41 BD241C dry jointed, DL22 BYW76 s/c | 14-09-04 |
| Thomson | ICC17 | LED gives 3 orange flashes | LOPTx | 14-09-04 |
| Thomson | ICC17 | No sound or vision - low humming | TS81 BC847B sm leaky c-e | 14-09-04 |
| Thomson | ICC17 21DK24U | St/by LED flashes - comes on using R/C but excess brill with fback lines | 196v HT to IB01 TDA6107Q RGB o/p chip missing on crt base - RB06 220R o/c | 14-09-04 |
| Thomson | ICC17 24WK24U | Tripping with red LED in sympathy | To disable trip s/c TL17 e-c; blank raster with fb lines now present; Field fback supply missing due to ZL11 MP25 o/c | 14-09-04 |
| Thomson | ICC17 28VK24 etc | Dead with red LED blinking 2 then 7 pulses | LOPTx - comes with mod kit 35175720. Also check FOP chip IF01 & cct prot ZL11 for damage by LOPTx | 14-09-04 |
| Thomson | ICC17 28WF25U | Dead with all volts appearing at psu o/p at 1/2 normal value briefly at sw on | The 39v I/p to TP21 chopper Tr in st/by psu low at 11 v - DP21 39v zener leaky | 14-09-04 |
| Thomson | ICC17 28WF25U | Int reverts to st/by with red LED flashing | May run again for a while when sw back on - leakage in focus spark gap. Fit new crt base pt no 80298800 | 14-09-04 |
| Thomson | ICC17 28WR25UG | Dead - no st/by light | DP21 37v zener BZX85C39 also check RP20 470R. | 14-09-04 |
|
|
| Thomson | ICC17 28WS23U | Dead apart from Red LED that does not change | LOPTx low res turns all ways round | 14-09-04 |
| Thomson | ICC17 28WS23U | Shuts down at sw on aft EHT rustles up | LOPTx replaced stopped shutting down but still no sound/vis - CB01 10nF 3kv in A1 supply on crt base leaky | 14-09-04 |
| Thomson | ICC17 28WS23U | Tuning procedure | Sw off TV mains whilst in st/by. Hold chan - on TV whilst sw on. Full auto tune menu appears | 14-09-04 |
| Thomson | ICC17 32WS22U | Dead - at sw on LED turns green then flashes amber twice, goes green then flashes amber 6 times & repeats | Dry joints CRT base | 14-09-04 |
| Thomson | ICC17 32WS23U | Trips 3 times then dead | LOPTr & LOPTx faulty | 14-09-04 |
| Thomson | ICC19 28DG35UB | Int shows pic but usually error code indicating faulty Txt | Replace Txt panel | 14-09-04 |
| Thomson | ICC19 28DG35UB | PIN code unsetting - "Type in 4 digit code" message | Hold down both prog & vol minus(-) button on TV & switch on. Release buttons & you should be in service mode.Navigate with arrow buttons on remote to "Setup" then select "Erase Pin" by holding down the right arrow button for 5 secs until yellow tick appears in box.You must backtrack to find the "Quit" option to exit & store the new info. | 14-09-04 |
| Thomson | ICC19 28DG35UB | Tuning mode | From st/by hold down menu button & the set will turn on in preset mode. Follow on screen prompts | 14-09-04 |